free hit counter
  1. Manuals
  2. Brands
  3. AXIOMTEK Manuals
  4. Motherboard
  5. SBC84820 Series
  6. User manual

AXIOMTEK SBC84820 Series User Manual

Pentium m all-in-one capa board with dualview display and sata
Hide thumbs Also See for SBC84820 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
SBC84820 Series
®
Pentium
M All-In-One
Capa Board
With DualView Display and SATA
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for AXIOMTEK SBC84820 Series

Summary of Contents for AXIOMTEK SBC84820 Series

  • Page 1 SBC84820 Series ® Pentium M All-In-One Capa Board With DualView Display and SATA User’s Manual...
  • Page 2 AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.

  • Page 3: Esd Precautions

    Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co., Ltd. ® Windows is a trademark of Microsoft Corporation. Phoenix & AWARD are trademarks of Phoenix Technology Ltd.

  • Page 4: Table Of Contents

    Table of Contents Disclaimers ......................ii ESD Precautions ....................iii Chapter 1 Introduction ..............1 Specifications ..................2 Utilities Supported ................... 5 Chapter 2 Jumpers and Connectors ..........7 Board Dimensions and Fixing Holes ............7 Board Layout ................... 9 Jumper Settings ..................
  • Page 5 The Main Menu ..................37 Standard CMOS Setup Menu..............38 Advanced BIOS Features..............41 Advanced Chipset Features ..............46 Integrated Peripherals ................48 Power Management Setup..............53 4.10 PnP/PCI Configuration Setup..............56 4.11 PC Health Status................... 58 4.12 Frequency/Voltage Control..............59 4.13 Load Optimized Defaults ...............
  • Page 6 MEMO...

  • Page 7: Chapter 1 Introduction

    +5V/12V power capability and that allow adoption of an extensive array of PC peripherals. The industrial-grade construction of SBC84820 series allows your system to endure the continuous operation in hostile environments where stability and reliability are basic requirements. System dependability of SBC84820 series are enhanced by its built-in watchdog timer, a special industrial feature not commonly seen on other motherboards.

  • Page 8: Specifications

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual ® Designed for the professional embedded developers, the Pentium embedded board SBC84820 Series is virtually the ultimate one-step solution for embedded system applications. Specifications ® ® ® LV Intel Pentium M and ULV Celeron...
  • Page 9 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual CompactFlash Socket One CompactFlash Type II Socket jumper selectable as Master or Slave and DMA mode supported Power 3.3V (Default) or 5V (Optional) Onboard Multi-I/O One floppy port supporting up to one devices (LS-120 or ZIP Bootable) One SPP/EPP/ECP parallel port with 26-pin 2.0 pitch box- header ;...
  • Page 10 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Ethernet: Dual Ethernet Fast/Gigabit Ethernet; standard for single LAN, 2nd is Optional from AX93208 stacking Board Wake On LAN (via ATX power supply) Equipped with RJ-45 interface optional Intel 82573V as Gigabit Audio: Realtek AC’97 codec audio Amplify for speaker-out with 2.5W for each channel...

  • Page 11: Utilities Supported

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Utilities Supported Chipset Driver Ethernet Driver VGA Driver Audio Driver Introduction...
  • Page 12 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual MEMO Introduction...

  • Page 13: Chapter 2 Jumpers And Connectors

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual C h a p t e r 2 Jumpers and Connectors Board Dimensions and Fixing Holes 104.65 98.37 98.37 6*M2.0 BOSS FAN1 94.74 87.76 79.14 64.26 62.74 56.64 44.20 40.76 34.54 34.14 CN11 3.18...
  • Page 14 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 114.55 66.80 44.96 24.26 26.42 72.39 96.01 47.00 66.93 146.05 Solder Side Jumpers and Connectors...

  • Page 15: Board Layout

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Board Layout Component Side Jumpers and Connectors...
  • Page 16 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Solder Side Jumpers and Connectors...

  • Page 17: Jumper Settings

    SBC84820 Pentium M All-In-One Capa Board User’s Manual Jumper Settings Proper jumer settings configure the SBC84820 Series to meet your application purpose. We are herewith listing a summary table of all jumpers and default settings for onboard devices, respectively. Jumper...

  • Page 18: Lvds Voltage Select Jumper (Jp2)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.3.2 LVDS Voltage Select Jumper (JP2) This jumper is to select the voltage for LVDS interface. Description Function Jumper Setting LVDS Voltage 3.3V (Default) Selection 2.3.3 COM1 Mode Select for RS-232/422/485 Jumpers (JP3, JP6, JP7) These jumpers select the COM1 port’s communication mode to operate RS-232 or RS-422/485.

  • Page 19: Com1 Mode Select Jumper (Jp4)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.3.4 COM1 Mode Select Jumper (JP4) These jumpers select the COM1 port’s DCD and RI mode. Description Function Jumper Setting COM1 (JP4) *Pin 1=DCD (Default) *Pin 1=5V *Pin 9=RI (Default) *Pin 9=+12V Jumpers and Connectors...

  • Page 20: Com2 Mode Select Jumper (Jp5)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.3.5 COM2 Mode Select Jumper (JP5) These jumpers select the COM2 port’s DCD and RI mode. Description Function Jumper Setting COM2 (JP5) *Pin 1=DCD (Default) *Pin 1=5V *Pin 8=RI (Default) *Pin 8=+12V 2.3.6 CMOS Clear Jumper (JP8) You may need to use this jumper is to clear the CMOS memory if...

  • Page 21: Audio Output Select Jumper (Jp9)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.3.7 Audio Output Select Jumper (JP9) This jumper makes the select of Audio output. Description Function Jumper Setting Audio Output Line Out Selection (Default) Speak Out 2.3.8 CompactFlash Setting Jumper (JP10) Use this jumper to set Master/Slave CompactFlash interface.

  • Page 22: Connectors

    Connectors connect the CPU card with other parts of the system. Loose or improper connection might cause problems. Make sure all connectors are properly and firmly connected. Here is a summary table shows you all connectors on the SBC84820 Series. Connectors Label...

  • Page 23: Digital I/O Port (Dio) Connector (Cn1)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.1 Digital I/O Port (DIO) Connector (CN1) The board is equipped an 8-channel digital I/O connector CN1 that meets requirements for a system customary automation control. The digital I/O can be configured to control cash drawers and sense warning signals from an Uninterrupted Power System (UPS), or perform store security control.

  • Page 24: Parallel Ide Connector (Cn3)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual mounted speaker unit or internal buzzer. While connecting the CPU card to an internal buzzer, please short pins 2-4; while connecting to an external speaker, you need to set pins 2-4 to Open and connect the speaker cable to pin 8 (+) and pin 2 (-).
  • Page 25 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Data 14 Data 0 Data 15 No connector DREG# Signal Signal Signal IOW # IOR # IOCHRDY CSEL DACK# Interrupt No connector PDIAG# HDC CS0 # HDC CSI # HDD Active # No connector CN17: 7-Pin SATA Connector Signal...

  • Page 26: Printer Port Interface Connector (Cn4)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.4 Printer Port Interface Connector (CN4) The board has one one 26-pin header connector CN4 for onboard parallel port LPT1. The onboard PRN is a multi-mode parallel port that supports: Standard mode: IBM PC/XT, PC/AT and PS/2™...

  • Page 27: Usb Connectors (Cn5, Cn12)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.5 USB Connectors (CN5, CN12) The board supports four Universal Serial Bus (USB) connectors compliant with USB 2.0 (480 Mbps) that can be adapted to any USB peripherals, such as monitor, keyboard, and mouse. The board has a box-header connector (CN5), and a double-deck port (CN12) for two USB connectors.

  • Page 28: Display Interface

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.6 Display Interface The 915GM/910GMLE Graphic Controller is a highly integrated graphics accelerator to deliver high performance 2D, 3D and video capabilities. The 915GM/910GMLE is a complete graphics solution with its interfaces to UMA using a DVMT configuration, an analog display (CRT port), a LVDS port for digital LCD connection, and optional second LVDS LCD interface (via Chrontel CH7308A converter).
  • Page 29 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual CN8: 7-pin Connector for Inverter Signal BKLT_EN CN6: 40-pin Connector for LVDS Flat Panel Signal Signal VCCM VCCM VCCM VCCM VCCM VCCM N.C. N.C. N.C. Channel B D0- N.C. Channel B D0+ Channel B CLK- Channel B D1- Channel B CLK+...

  • Page 30: Atx Power Connector (Cn7)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.7 ATX Power Connector (CN7) Steady and sufficient power can be supplied to all components on the board through the power connector. Please make sure all components and devices are properly installed before connecting the power connector.

  • Page 31: Serial Port Interface Connectors (Cn9, Cn15)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.8 Serial Port Interface Connectors (CN9, CN15) The board has two onboard serial ports, COM1 (RS-232/422/485) and COM2 (RS-232). They are jumper selectable with auto flow control features. All ports supply +5V power capability on DCD, and +12V on RI (excluding 5V), depending on jumper setting.

  • Page 32: Lan Connector (Cn10)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.9 LAN Connector (CN10) The RJ-45 connector is for Ethernet. To connect the board to a 100/10 Base-T hub, just plug one end of the cable into CN10, and connect the other end (phone jack) to a 100/10-Base-T hub.

  • Page 33: Keyboard & Ps/2 Mouse Port Connector (Cn13)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.11 Keyboard & PS/2 Mouse Port Connector (CN13) The board supports a keyboard and Mouse interface. Connector CN13 is a DIN connector for PS/2 keyboard Connection VIA “Y” Cable. Signal Keyboard Data CN13 Mouse Data Keyboard Clock...

  • Page 34: Fdd Connectors (Cn18)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.13 FDD Connectors (CN18) The board has a 26-pin FCC Z.I.F. type connector CN18 to support a single floppy drive, which can be 3.5” 720 KB or 1.44 MB/2.88 MB types of FDD drives. CN18: Floppy Connector Signal Signal...
  • Page 35 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Signal Signal CD1# Data 3 Data 11 Data 4 Data 12 Data 5 Data 13 Data 6 Data 14 Data 7 Data 15 CS0# CS1# Address 10 VS1# ATASEL IORD# Address 9 IOWR# Address 8 Address 7...

  • Page 36: Fan Connector (Fan1)

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 2.4.15 FAN Connector (FAN1) Pentium microprocessors require a fan for heat dispensing. FAN1 is a fan connector for CPU and system, supplying power to the fan. Signal FAN1 +12V Sensor Jumpers and Connectors...

  • Page 37: Chapter 3 Hardware Description

    Make sure your installed microprocessor with all correct settings that prevent the CPU from damages. BIOS The SBC84820 Series uses Phoenix-Award Plug and Play BIOS with a single 4Mbit Flash. System Memory The SBC84820 Series industrial CPU card supports one 200-pin DDRII SO-DIMM socket for a maximum memory of 1GB DDRII SDRAMs.

  • Page 38: I/O Port Address Map

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual I/O Port Address Map ® ® ™ The Intel Pentium M and Celeron M CPUs can make communication via I/O ports. It has a total of 1 KB port addresses available for assignment to other devices via I/O expansion cards. I/O Port Address Map (1) Hardware Description...
  • Page 39 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual I/O Port Address Map (2) Hardware Description...

  • Page 40: Interrupt Controller

    M All-In-One Capa Board User’s Manual Interrupt Controller The SBC84820 Series is a 100% PC compatible control board. It consists of 16 interrupt request lines. The mapping list of the 16 interrupt request lines is shown as the following table.

  • Page 41: Chapter 4 Award Bios Utility

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual C h a p t e r 4 Award BIOS Utility The Phoenix-Award BIOS provides users with a built-in Setup program to modify basic system configuration. All configured parameters are stored in a battery-backed-up RAM (CMOS RAM) to save the Setup information whenever the power is turned off.

  • Page 42: Control Keys

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Control Keys Up arrow Move cursor to the previous item Down arrow Move cursor to the next item Left arrow Move cursor to the item on the left hand Right arrow Move to the item in the right hand Main Menu -- Quit and delete changes into CMOS Esc key...

  • Page 43: The Main Menu

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual The Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from ten setup functions and two exit choices. Use the arrow keys to select the setup function you intend to configure then press <Enter>...

  • Page 44: Standard Cmos Setup Menu

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Standard CMOS Setup Menu The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp>...
  • Page 45 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual IDE Primary Master / Primary Slave The categories identify the types of one channel that have been installed in the computer. There are 45 predefined types and 2 users definable types are for Enhanced IDE BIOS. Type 1 to Type 45 is predefined.
  • Page 46 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Halt On This field determines whether the system will halt if an error is detected during power up. The system boot will halt on any error detected. No errors (default) Whenever the BIOS detect a non-fatal error, the All errors system will stop and you will be prompted.

  • Page 47: Advanced Bios Features

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Hard Disk Boot Priority Scroll to this item and press <Enter> to view the sub menu to decide the disk boot priority.
  • Page 48 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Virus Warning This option flashes on the screen. During and after the system boot up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system with the following message. You can run an anti-virus program to locate the problem.
  • Page 49 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual First/Second/Third Boot Device These items allow the selection of the 1 , and 3 devices that the system will search for during its boot-up sequence. The wide range of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and CDROM.
  • Page 50 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Typematic Rate Setting This determines the typematic rate of the keyboard. The default value is “Disabled”. Enabled Enable typematic rate and typematic delay programming Disable typematic rate and typematic delay Disabled programming.
  • Page 51 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual NOTE To disable security, select PASSWORD SETTING at Main Menu and then you will be asked to enter password. Do not type anything, just press <Enter> and it will disable security. Once the security is disabled, the system will boot and you can enter Setup freely.

  • Page 52: Advanced Chipset Features

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Advanced Chipset Features Since the features in this section are related to the chipset on the CPU board and are completely optimized, you are not recommended to change the default settings in this setup table unless you are well oriented with the chipset features.
  • Page 53 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual accumulate its charge before refresh. System Memory Frequency This item helps you set main memory frequency. When using an external graphics card, it can be adjusted to enable the best performance for your system. System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance.

  • Page 54: Integrated Peripherals

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Integrated Peripherals This section allows you to configure your SuperIO Device, IDE Function and Onboard Device. OnChip IDE Device Scroll to this item and press <Enter> to view the sub menu OnChip IDE Device.
  • Page 55 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual IDE DMA transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention. This improves data throughput and frees CPU to perform other tasks. On-Chip Primary/Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels.
  • Page 56 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual SATA Port If the “PATA IDE Mode“ is Primary, it will show ” P1, P3 is Secondary” which means SATA 2 and SATA 4 are Secondary. If the “PATA IDE Mode “ is Secondary, it will show “...
  • Page 57 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Onboard Device USB Controller Enable this item if you are using the USB in the system. You should disable this item if a higher-level controller is added. USB 2.0 Controller Enable this item if you are using the EHCI (USB2.0) controller in the system.
  • Page 58 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Super IO Device Onboard FDC Controller Select Enabled, if your system has a floppy disk controller (FDC) installed on the system board and you want to use it. If you install and-in FDC or the system has no floppy drive, select Disabled in this field.

  • Page 59: Power Management Setup

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Press <Esc> to return to the Integrated Peripherals page, and press it again to the Main Menu page. Power Management Setup The Power Management Setup allows you to save energy of your system effectively.
  • Page 60 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual your operating system supports ACPI, such as Windows 98SE, Windows ME and Windows 2000, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field.
  • Page 61 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual The System will never enter the SUSPEND mode. Disabled 1/2/4/6/8/10/2 It defines continuous idle time before the system 0/30/40 entering the SUSPEND mode. Min/1 Hr If any item defined in (J) is enabled and active, the SUSPEND timer will be reloaded.

  • Page 62: Pnp/Pci Configuration Setup

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual from entering a power saving mode or can awaken the system from such a mode. Primary/Secondary IDE 0/1 Use this item to configure the IDE devices monitored by the system. FDD, COM, LPT Port Use this item to configure the FDD, COM and LPT ports monitored by the system.
  • Page 63 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual Normally, you leave this item Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup or if installing a new add-on cause the system reconfiguration a serious conflict that the operating system can not boot. Options: Enabled, Disabled.

  • Page 64: Pc Health Status

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 4.11 PC Health Status This section supports hardware monitering that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board. Current GMCH Temperature The current GMCH temperature will be automatically detected by the system.

  • Page 65: Frequency/Voltage Control

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 4.12 Frequency/Voltage Control This section is to control the CPU frequency and Supply Voltage, DIMM OverVoltage and AGP voltage. Auto Detect PCI Clk The enabled item can automatically disable the clock source for a PCI slot without a module, to reduce EMI (ElectroMagnetic Interference).

  • Page 66: Load Optimized Defaults

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 4.13 Load Optimized Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter “N”.

  • Page 67: Set Supervisor/User Password

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 4.14 Set Supervisor/User Password You can set a supervisor or user password, or both of them. The differences between them are: Supervisor password: You can enter and change the options on the setup menu.

  • Page 68: Save & Exit Setup

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual 4.15 Save & Exit Setup This allows you to determine whether or not to accept the modifications. Typing “Y” quits the setup utility and saves all changes into the CMOS memory. Typing “N” brigs you back to Setup utility. 4.16 Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session.

  • Page 69: Appendix A Watchdog Timer

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual A p p e n d i x A Watchdog Timer Watchdog Timer Setting After the system stops working for a while, it can be auto-reset by the Watchdog Timer. The integrated Watchdog Timer can be set up in the system reset mode by program.
  • Page 70 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual ; IF to disable WDT: O 2E 30 O 2F 00 ; Can be disable at any time Timeout Value Range 1 to 255 Minute / Second Program Sample Watchdog Timer can be set to system reset after 5-second timeout. 2E, 87 2E, 87 2E, 07...

  • Page 71: Appendix B Digital I/O

    ® SBC84820 Pentium M All-In-One Capa Board User’s Manual A p p e n d i x B Digital I/O Signal Signal Digital Input 1 Digital Output 1 Digital Intput 2 Digital Output 2 Digital Output 3 Digital Output 4 Using the Digital Input Function Start ↓...
  • Page 72 ® SBC84820 Pentium M All-In-One Capa Board User’s Manual O 2E F1 I 2F XX( XX is input Data; if no input source,the value is C0) Using the Digital Output Function Start ↓ Un-Lock SuperI /O: O 2E 87 ; Un-lock super I/O O 2E 87 ;...

Table of Contents